Hi! I want to ask that my balls are quite small and hanging rather high that sometimes it might retreat back into my body. I’ve tried various cages and always find the problem of either balls slip through the gap or it will cause pain in the balls.
Anyone have some idea on which cage should I pick?
when do you know you can size down your cage? i’ve been using this one for a little while now
How does it look on size? Considering going smaller. 3 curved ring with N+
Finally got it. Using the N+ cobra with the #5 curved ring. Tried the #4 and felt too tight on my balls in the shop but now I'm thinking I should have got it as I used some coconut oil to reduce friction under my sack and a ball slipped through 😬 tied myself in now and way more secure...
Hi all,
Long time reader, first time caller. LOL
I am seeking the advice of the experts. I have been using a K3D N+ Cobra and Viper and everything fits great. The one exception is that my urethra doesn't always cooperate and line up with the exit holes. I have a little better luck with the Cobra than I do with the Viper.
This is the last little thing that keeps this from being a "perfect" experience. I will line it up when I put the device on but after a while and some growth, shrinkage, shifting, it gets out of alignment and ultimately makes a mess.
Yes, yes, I know...it's all a part of the experience, but I feel like it doesn't have to be that way. I have to constantly adjust before I go and in some cases when I've been holding it too long, that's a challenge.
Has anyone else encountered this and able to find a solution? Does this mean that I need to size down? Or is this something that I'll "just have to deal with"?
Any insight or advice is appreciated.
Hi everyone,
I need your help. I want to buy a KINK3d cage but i don't want to make a mistake since they are pretty expensive.
See picture for measurements (i did my best, srry no real pics, i am still not sure about posting my dick on the internet)
My flaccid penis is about 4 inch long. The circumference along the shaft goes in between 4 and 4.75 inch.
I have purchased this cage for trying the ring and cage size.
I was able to get in the 50 mm ring but it was incomfortable and i could feel pain on the left ducts, blood vessel and ligaments. I did the string test for measurement i a was about 15.25 cm with the rope pretty tight. I tried measuring it with a measuring tape. 18 cm was the best i could get it tight around.
My other problem with the amazon cage is that it was difficult to insert my penis in the cage itself. I had to force it. I was able to get it in one time. I also had a lot of skin fold since i am uncut.
So i was thinking on going with a Viper S+. I don't know what to do for the ring size. Is size 5 (54 mm) going to be ok or to tight again. On the website it says that size 6 and 7 are usually to big.
Also i don't know if i need to go wide or standard for cage width.
I appreciate all the input you can get me.
Hopefully it can wear standard no4 with comfort. Might order XD no4 for a smaller gap. Might even downsize from Viper S standard to Viper N+ standard 😜🔐
Recently got my new cage but I’m not sure if it’s a good fit. It’s comfortable when I’m soft but it’s very obvious through my pants and I feel like it points forwards too much. I was planning on wearing it long term and in the gym and stuff, but I can’t since it’s visible through my clothes
This is a follow-up on my topic two sizes. I can not post a pic there anymore.
I have been aroused in the shop. I am more a shower than a grower, so the thickness looked so that I needed the bfg. It was the first time experience ofcourse.
Since I wore the cage today at work and there is enough distraction to be fully flaccid, I now know that I need a shorter cage. I now have the bfg wide.
I took length and, as before, the length is almost 11 centimeter. I may change the cage in the shop. What do you think? Should I change to a Cobra S+ ?
I asked for the cage this morning. I wonder how long she’ll keep me like this